How to estimate a painting job and prepare your bid

Work out your paint, time and costs, then turn them into a clear bid your customer can understand.

3D contractor measuring a living-room wall beside paint cans, a roller and floor protection

Before you start

  • Price the actual surfaces, preparation and access for your job.
  • Count person-hours and add overhead and profit only once.
  • Give your customer a clear scope, price and separately priced options.

To estimate a painting job, measure the surfaces, work out paint and prep, and price the person-hours and other costs. Then add overhead and profit once, and give your customer a clear scope with a price. The example below prices interior walls only, so you can see each step before you apply it to your own bid.

Define the scope before you measure

Your price is only as good as the scope behind it. Before you count square feet, settle which rooms or work areas are included and what gets painted in each: walls, ceilings, trim, doors. Note any color changes, the finish or sheen, and how many coats the chosen product system needs.

Then settle the practical items. How much prep is included, and how much furniture moving and protection? When can you work, and is the space occupied? Who buys the paint, and are return visits likely? Does your price cover cleanup and disposal? If rooms differ in prep or how fast you can work them, price them as separate work areas instead of averaging them.

Older or damaged coatings that need a specialist assessment sit outside an ordinary painting price until someone has checked them. Say so on the bid rather than guessing.

Worked example: 1,000 sq ft of interior walls

These are sample prices in USD; use your own costs for your job.

The scope is interior walls only. You measured 1,200 sq ft of gross wall area and subtracted 200 sq ft of openings, which leaves 1,000 net sq ft. The existing paint has been assessed as suitable for a two-finish-coat system with no separate primer. Minor prep fits in eight hours. Extensive repairs, ceilings, trim, doors and any specialist remediation are excluded. If the real product or surface needs primer or more repair, price that separately before you quote.

Paint quantity

Two coats over 1,000 net sq ft is 2,000 sq ft of coverage. At a sample spread rate of 350 sq ft per US gallon, that's 5.714 gallons. Add an illustrative 10% application allowance and you get 6.286 gallons. Round up to seven one-gallon cans of the same product and color.

Use the coverage on your product's spec sheet and choose an allowance for the surface and application method. The coverage and allowance above are example inputs. The Benjamin Moore paint calculator is useful for product planning, but it gives approximate quantities. It assumes two coats and leaves out the ceiling, so check it against your own scope.

If the job has more than one color or finish, calculate and round each one separately. Don't pool different paints into one total. The paint calculator handles quantities only, so use it for the gallon count and do your pricing elsewhere.

For the pricing step, Construction Job Estimator can bring in real-time material prices from local suppliers, so your cost per can comes from current prices rather than the $35-per-can sample below. You can still edit any price to match your own costs.

Labor and other costs

The sample labor cost is $35 per person-hour, including employment costs where applicable. It leaves out business overhead and profit. If you work on the job yourself, cost your own time too.

A person-hour is one person working for one hour, so two workers for four hours is eight person-hours. Count hours worked, not elapsed days. Drying time affects your schedule, but it isn't automatically staffed time, and it isn't automatically free either. Charge for the labor, waiting and return visits your actual plan involves. The sample hours below already reflect the work plan for this job, so change them to match yours.

Cost item Calculation USD
Finish paint 7 cans × $35 245
Supplies and consumables 55
Materials 300
Protection and minor prep 8 person-hours × $35 280
Application 12 person-hours × $35 420
Cleanup 2 person-hours × $35 70
Labor 22 person-hours 770
Job travel and parking 40
Equipment rental 40
Other direct expenses 80
Direct costs 300 + 770 + 80 1,150
Allocated overhead 10% of direct costs 115
Total job cost 1,265
Markup 20% of job cost 253
Price before applicable tax 1,518

Add overhead and profit once

Overhead covers the cost of running the business that you can't pin to one job. The 10% above is an illustration, not a recommended norm. Your figure should come from your own budget and a realistic amount of chargeable work. Keep each expense in one place. If vehicle or equipment costs are already in your overhead, don't list them again as direct expenses.

Markup is a percentage added on top of your cost. Margin is the share of the final price that's profit. Here, 20% markup on a $1,265 cost leaves $253 after the costs and overhead we allowed. That is 16.67% of the $1,518 price. So this price carries a 16.67% margin, not a 20% margin. If you aim for a particular margin, work backward from that target. The contractor markup calculator shows both numbers side by side.

Also watch for double counting. If you already charge a fully loaded selling rate that includes overhead and profit, don't add them again on top.

As a sanity check, $1,518 over 1,000 net wall sq ft is about $1.52 per sq ft. That's a check on this job only. It isn't a general rate, and it isn't a floor-area figure.

How do painters charge for a job?

Painters usually charge in one of three ways. The right one depends on how well you can define the work before you start.

Fixed scope and total. You give one price for a written scope that names the rooms, surfaces, coats and exclusions. It works best when you can measure and describe the job, and it's the method the example above uses.

Hourly. This suits work you can't judge until you open it up, such as repairs behind old finishes. Agree the hourly rate and how hours will be recorded with your customer before you begin. Bill the hours actually worked, and keep your cost rate separate from the rate you charge.

Square-foot unit rate. State whether the rate uses painted surface area or floor area; they are different measurements. This guide uses net wall area after openings. Price trim and doors separately where their detail makes a wall-area rate unsuitable. State the basis on the bid so nobody mixes up the two.

You can work a unit rate out of a priced job. The sample price of $1,518 divided by 1,000 net wall sq ft is $1.518, about $1.52 per net wall sq ft in USD. That figure already carries the overhead and markup for this one scope.

It isn't a universal rate. It also doesn't replace your checks on surface condition, masking, furniture moving, working height, number of coats and whether the space is occupied. Any of those can change the hours, and the rate has to follow.

Whichever method you pick, your customer should still see the scope and price laid out as described in the next section.

What goes on the bid

Your customer needs a clear scope and a price, not your internal cost sheet. For this example, a short written bid would say:

  • Price of $1,518 before applicable tax
  • Interior walls in the named rooms, about 1,000 sq ft
  • The agreed minor prep and protection
  • The selected product, finish and color, applied in two finish coats
  • Cleanup
  • The exclusions: extensive repairs, ceilings, trim, doors and specialist remediation

Confirm how your own taxes apply separately. Beyond scope and price, include how long the bid is valid, your start window, payment terms and your contact details. Say how extra work gets handled too. If something changes, agree it with the customer before you do it and send a revised bid.

Check the scope before you submit your painting bid

Look at the job before you give a firm price. When a tender or request is vague, ask for a room and surface schedule, the paint specification, access details and any working restrictions, such as an occupied site or limited hours. Build those conditions into your hours before you send a price.

Price optional work as separate line items using your own costs. If the customer might want ceilings, trim or repairs, list each one as an option with its own price. Make clear which options are outside the main price, so your customer knows what they are choosing.

When you're up against other bids, compare what each one includes: prep, number of coats and products. A lower total may simply mean less work was priced. Don't match it by dropping work you never mentioned, and don't discount below your checked costs. Follow up after the date the customer gave for a decision, and use that call to clear up scope questions.

A note for Canadian contractors

Use your own CAD material and labor costs, not the USD figures here relabeled. Take quantities from the actual pack labels and product coverage, and keep US gallons, Imperial gallons and liters distinct when you convert.

Next step: build the estimate and the bid

To put your bid together, the painting estimate template offers a blank PDF, a completed example PDF, an Excel file and a browser editor, all free with no signup. The material and labour cost calculator is handy for checking your totals.

If you'd rather not build every line by hand, you can describe the job to Construction Job Estimator by voice or text, add site photos, and get a working estimate in minutes. Materials, labor and other job costs sit in one estimate, and you can see the quantities, prices and labor behind each figure. Check them against your scope and exclusions, change anything that doesn't fit, then prepare the estimate or quote for your customer. If you're changing colors, a before-and-after render can help your customer picture the finished look. Once the job is approved, you can convert the estimate into an invoice.

Choosing software to put your next bid together? Compare estimating apps for painting contractors, including options for site visits, painting production rates and commercial plans.

Pricing a house exterior? Our exterior painting estimating guide covers wall and gable measurements, preparation, access and weather, with a separate worked quote.

Pricing work for a general contractor or an occupied business? See how to bid on a commercial painting job for finish schedules, phased access and bid submissions.

← Back to all guides

Construction Job Estimator

Your next estimate.
Ready in minutes.

Tell us what needs doing. Get real-time material prices from local suppliers, bring your labour and other costs together, and send your customer a professional estimate.

Take the next job from description to estimate.

★★★★★ Used by 10k+ contractors